等质量异形粒子超高速撞击侵蚀

用数值方法模拟双锥，圆柱，椭球、圆锥和倒圆锥五类等质量异形铝粒子五种高宽比共２５种粒子对半无限铝靶的超高速撞击侵蚀，撞击速度为４ｋｍ／ｓ，给出了坑深、坑径、坑形参数和坑体积随粒子形状及高宽比的变化曲线。结果与非圆球异形粒子超高速撞击侵蚀计算有重要参考价值。     

单/双轴预拉载荷对碳纤维复合材料高速冲击性能的影响研究

针对发动机工作时受预载荷的叶片受到外物冲击的情况,设计一种面内单轴及双轴预加载装置,开展单轴与双轴不同大小预拉载荷下碳纤维/环氧树脂复合材料（T700/TDE-86）的高速冲击试验,探究预拉载荷对复合材料抗冲击性能的影响,并结合超声C扫描分析预拉载荷对损伤面积的影响。结果表明：面内初始载荷对复合材料层合板抗冲击性能和分层损伤面积有显著影响;预拉载荷会提高靶板的抗弯刚度,减少靶板吸收的能量,减小弹道极限,且在双轴预拉情况下更明显;弹体击穿靶板后分层损伤面积几乎不变,而预拉载荷会减小分层损伤面积,且在双轴预拉情况下更明显。     

APU 转子爆破对防火墙影响的研究

APU是安装在民用飞机上的辅助动力装置,是飞机上重要的部件,因此必须考虑APU 转子爆破时小碎片对飞机安全的影响。通过有限元软件LS-DYNA,分别模拟了APU 转子爆破时小碎片对APU 防火墙以及3种不同厚度加强板的冲击计算。根据数值计算结果,选择合适的加强板方案,既能防止防火墙碰撞区被小碎片击穿,同时付出的重量代价又较小。通过对APU 防火墙增加加强板,确保APU 转子爆破时飞机的安全 性,满足AC20-128A 的设计要求。     

典型民机复合材料损伤分析及敲击检测

只有充分研究民机典型复合材料损伤机理,才能在复合材料的应用中最大限度地减少和避免其损伤,并且为复合材料的损伤修理奠定基础.通过对民机典型复合材料损伤的研究,分别从材料、设计、结构、制造与使用等方面入手,通过细观破坏机制阐述了层合复合材料的损伤.对部件的检测进行理论分析,找到易损伤位置,采用微观破坏机制运用敲击检测法对胶接复合材料就行了损伤检测,验证了二者的结合可提高检测效率及准确率.     

Emergence of a Habitable Planet

We address the first several hundred million years of Earth’s history. The Moon-forming impact left Earth enveloped in a hot silicate atmosphere that cooled and condensed over ∼1,000 yrs. As it cooled the Earth degassed its volatiles into the atmosphere. It took another ∼2 Myrs for the magma ocean to freeze at the surface. The cooling rate was determined by atmospheric thermal blanketing. Tidal heating by the new Moon was a major energy source to the magma ocean. After the mantle solidified geothermal heat became climatologically insignificant, which allowed the steam atmosphere to condense, and left behind a ∼100 bar, ∼500 K CO₂ atmosphere. Thereafter cooling was governed by how quickly CO₂ was removed from the atmosphere. If subduction were efficient this could have taken as little as 10 million years. In this case the faint young Sun suggests that a lifeless Earth should have been cold and its oceans white with ice. But if carbonate subduction were inefficient the CO₂ would have mostly stayed in the atmosphere, which would have kept the surface near ∼500 K for many tens of millions of years. Hydrous minerals are harder to subduct than carbonates and there is a good chance that the Hadean mantle was dry. Hadean heat flow was locally high enough to ensure that any ice cover would have been thin (<5 m) in places. Moreover hundreds or thousands of asteroid impacts would have been big enough to melt the ice triggering brief impact summers. We suggest that plate tectonics as it works now was inadequate to handle typical Hadean heat flows of 0.2–0.5 W/m². In its place we hypothesize a convecting mantle capped by a ∼100 km deep basaltic mush that was relatively permeable to heat flow. Recycling and distillation of hydrous basalts produced granitic rocks very early, which is consistent with preserved >4 Ga detrital zircons. If carbonates in oceanic crust subducted as quickly as they formed, Earth could have been habitable as early as 10–20 Myrs after the Moon-forming impact.     

Numerical Simulation of Impact Loading on Solid Propellant Within an Orthotropic Shell

The strain–stress state of the solid propellant rocket engines (SPREs) is simulated under impact. The effect of orientation of elastic and strength properties of orthotropic organoplastic shell material on the strain–stress state of the solid propellant is investigated. Normal and oblique impact of single steel cylinder projectiles, both simultaneous and at different times of multiple, converging steel spheric particles with SPRE are investigated in this study. The investigation is conducted numerically. The numerical modeling was carried out in a three-dimensional formulation by the method of finite elements for the continuous approach of the mechanics of a deformable solid. The destruction of the anisotropic material is described by the tensor-polynomial criterion of the fourth degree, which takes into account the influence of hydrostatic pressure.     

航天器舷窗玻璃超高速撞击损伤与M/OD撞击风险评估

用北京卫星环境工程研究所的18mm口径二级轻气炮(TLGG)和20 J激光驱动微小飞片装置(LDFF-20)对用作航天器舷窗玻璃的熔融石英玻璃的超高速撞击损伤特性进行了实验研究和分析.其中,TLGG发射的球形铝弹丸直径分别为1 mm和3 mm,速度2～6.5 km/s;LDFF-20发射的圆柱形飞片厚度7 μm,直径1 mm,速度1～8.3 km/s.撞击结果为:对12 mm厚的熔融石英玻璃,直径为3mm的弹丸甚至在2.8 km/s的低速下就将其穿透,而直径为1 mm的弹丸在6.5km/s的高速下没有穿透,这说明弹丸直径对撞击损伤特性有很强的影响;LDFF-20发射的微小飞片的撞击仅在玻璃表面产生很浅的凹坑,没有裂纹产生,但微小飞片的累积撞击损伤明显地降低了玻璃的透光性.实验初步获得了侵彻深度PC、侵彻直径D1与弹丸撞击速度Vp、弹丸质量Mp之间的经验关系.依据实验结果和目前的微流星体/空间碎片(M/OD)环境工程模型,建议对于高度为400 km、轨道倾角42°、寿命为3年的典型航天器,其舷窗玻璃的临界安全(非穿透)厚度至少为12mm.     

一种新型空间微小碎片超高速碰撞试验地面模拟方法

文章简要叙述了空间微小碎片环境及其对航天器的影响,同时介绍了一种新型空间微小碎片超高速碰撞地面模拟方法——激光驱动飞片技术。     

复合材料蜂窝夹芯板低速冲击后的压缩

对含低速冲击损伤的Nomex蜂窝夹芯板试件进行了压缩实验,用X光技术、热揭层技术和外观检测等对压缩破坏损伤发展的过程进行了研究,分析了压缩破坏机理,结果表明:剩余压缩强度随冲击能量的增加而减少;夹芯板的压缩破坏主要由前面板控制,前面板发生局部屈曲的载荷与板的压缩破坏载荷几乎相等;表面玻璃布不仅能减少冲击损伤,而且能使板内的损伤显露在表面,容易让人发现.     

压气机叶片外物损伤模拟的撞击能量当量法

在分析外物与叶片间的运动态势后,提出压气机叶片外物员伤模拟的撞击能当量法,即使得摆锤的势能与外物摘击叶片时可能达到的功能相等。据此,设计并制作了摆锤装置,并实验观察到钛制压气机叶片损伤形态与撞击能量间的变化关系,即随着撞击能量的增加,损伤形态产生的顺序为,压痕→突缘→裂纹→突缘呈４５°剪切破坏,这与外场收集到的叶片的前缘损伤形态一致,同时,采用了ＴＣ４压气机叶片进行了相应的高周疲劳试验,验证了方法